Ferris Snapper Pro 84006412 PTO Clutch | 250 FT-LBS Water Guard OEM Clutch

Ferris / Snapper Pro 84006412 Genuine OEM PTO Clutch - 250 FT-LBS Water Guard

The Ferris / Snapper Pro 84006412 PTO Clutch is a genuine OEM replacement clutch for select Ferris and Snapper Pro commercial zero-turn mower applications. This is an OEM clutch, not an aftermarket replacement, and is commonly used on select Ferris ISX3300, Ferris IS3200Z, Ferris F320Z, and Snapper Pro S200XT models where specified by the parts diagram.

This clutch is listed as CLUTCH, 250 FT-LBS, WATER GUARD. Ferris / Snapper Pro part number 5108850 supersedes to 84006412. This part also replaces prior MPN 5105060 where specified. The clutch is an authentic Warner 5228-68, which replaces Warner 5228-52.

Always verify your full mower model number, serial number, engine, PTO group, original clutch part number, bore size, pulley specs, wiring connector, mounting style, and parts diagram before ordering. Do not order by mower series or deck size alone.

Product Details

Easy Model Fitment Guide

Use the dropdowns below to review common model references. This is a where-used reference list, not a fitment guarantee. Always check your mower’s parts diagram to confirm it uses 84006412, 5108850, 5105060, Warner 5228-68, or Warner 5228-52.

Important: This is a where-used reference list. PTO clutch fitment depends on the exact model, serial number, engine, crankshaft size, bore, pulley, belt alignment, electrical connector, anti-rotation bracket, mounting bolt, and parts diagram.

Key Features

• Genuine OEM Ferris / Snapper Pro PTO clutch
• Part number 84006412
• Replaces 5108850 and 5105060 where specified
• Authentic Warner 5228-68 clutch
• Replaces Warner 5228-52 where specified
• 250 ft-lbs rated torque
• Water Guard clutch design
• 1.125" bore / inside diameter
• 6.445" pulley flange outside diameter
• Used on select Ferris ISX3300, IS3200Z, F320Z, and Snapper Pro S200XT models
• OEM quality for proper fit and reliable PTO engagement

Why Choose an OEM PTO Clutch?

A PTO clutch must match the mower’s crankshaft, pulley alignment, belt system, wiring connector, torque rating, and anti-rotation setup. Using the wrong clutch can cause belt misalignment, poor blade engagement, wiring damage, vibration, overheating, or clutch failure.

Ferris / Snapper Pro 84006412 is the correct OEM replacement when your parts diagram lists 84006412, 5108850, 5105060, Warner 5228-68, or Warner 5228-52.

• OEM fit for compatible Ferris and Snapper Pro applications
• Designed for the correct crankshaft bore and pulley setup
• Helps restore proper blade engagement
• Reduces guesswork compared to universal PTO clutches
• Factory-correct replacement for listed mower models

When to Replace a PTO Clutch

Replace the PTO clutch if the blades will not engage, the clutch slips, the clutch overheats, the bearing is noisy, the pulley is damaged, or electrical testing confirms the clutch is not operating correctly. Always inspect the PTO switch, wiring harness, battery voltage, fuses, belts, idlers, and deck pulleys before replacing the clutch.

• Blades will not engage
• PTO clutch clicks but does not spin the deck belt
• Blades engage intermittently
• Clutch slips under load
• Clutch bearing is noisy or rough
• Clutch pulley is worn, damaged, or overheated
• Electrical connector or clutch wires are damaged
• Your parts diagram lists 84006412, 5108850, or 5105060

Important Fitment Notes

• This listing is for Ferris / Snapper Pro part number 84006412
• Replaces 5108850 and 5105060 where specified
• Warner reference: 5228-68, replacing 5228-52
• Verify your original clutch part number before ordering
• Confirm bore size, pulley size, torque rating, wiring connector, and anti-rotation bracket setup
• Do not order by mower series or deck size alone
• Inspect belts, idlers, pulleys, wiring, PTO switch, and charging system during diagnosis

Pre-Purchase Checklist

Before ordering Ferris / Snapper Pro 84006412, confirm:

• Your mower parts diagram lists 84006412, 5108850, 5105060, Warner 5228-68, or Warner 5228-52
• Your full model number matches the correct engine and PTO group
• Your mower uses a 1.125" bore clutch
• Your pulley flange outside diameter matches 6.445"
• Your application requires a 250 ft-lbs Water Guard PTO clutch
• Your wiring connector and anti-rotation setup match the original clutch
• Your PTO belt and deck pulley system are in good condition

Installation and Service Notes

PTO clutch replacement should be performed with the mower parked on level ground, key removed, parking brake engaged, blades disengaged, and the battery disconnected. Disconnect the negative battery cable first and reconnect it last.

• Take a photo of the original clutch wiring and mounting position before removal
• Inspect the crankshaft, keyway, mounting bolt, washer, and anti-rotation bracket
• Check the PTO belt, idlers, deck pulleys, and tensioning system
• Install the clutch fully seated and aligned with the belt path
• Route wiring safely away from belts, pulleys, hot surfaces, and moving parts
• Torque the clutch mounting bolt according to the mower service manual
• Reconnect the battery and test PTO engagement safely

Part Number / Search Terms

Ferris / Snapper Pro 84006412 may also be searched as:

• Ferris 84006412
• Snapper Pro 84006412
• 84006412 PTO clutch
• Ferris 5108850
• Snapper Pro 5108850
• Ferris 5105060
• Snapper Pro 5105060
• Warner 5228-68
• Warner 5228-52
• Ferris PTO clutch
• Snapper Pro PTO clutch
• Ferris ISX3300 PTO clutch
• Ferris IS3200Z PTO clutch
• Ferris F320Z PTO clutch
• Snapper Pro S200XT PTO clutch
• 250 ft-lbs PTO clutch
• Water Guard PTO clutch
• 1.125 bore PTO clutch
• commercial zero turn PTO clutch
• OEM Ferris clutch
• OEM Snapper Pro clutch

Frequently Asked Questions

P&P Small Engines stocks genuine Ferris and Snapper Pro PTO clutches, belts, blades, pulleys, spindle assemblies, filters, oils, electrical parts, and OEM replacement parts for commercial zero-turn mowers and outdoor power equipment.