Prepping your trusty 2X or 3X snow thrower for yet another winter, or getting ready to face its first blizzard, these snow thrower maintenance tips can help ensure you're prepared for cold and snowy weather this winter.
INSTRUCTIONS:
Step 1: Prepare your snow blower for maintenance.
Place your snow blower on a flat surface. Turn the engine off and let it cool down. Remove the safety ignition key to prevent accidental starting of the engine.
Step 2: Change the engine oil in your snow thrower.
Best to have the engine warm. Drain plug is usually located on the bottom side of the engine. Drain oil into pan. Refill to proper level with 5w30 engine oil. This should also be done after the first five hours of use.
Step 3: Install a new spark plug if necessary.
Check your spark plug at the start of every season. Its best just to replace spark plug every year.
Step 4: Inspect belts for wear.
Remove the belt cover to inspect the belts. If you see any wear or cuts in the belts now is the time to replace them. It's wise to keep a extra set of belts and shear pins on hand so you can make replacements quickly when necessary.
Step 5: Fuel tank.
Drain the fuel tank and replace with fresh fuel. Check and replace fuel filter if your machine has one.
Best to use premium fuel and add stabilizer, so it stays fresh longer. Consider starting it every so often if it sits for an extended period.
The Difference Between Winter-and Summer-Blend Gas: Refiners often blend winter gasoline with butane, a relatively inexpensive additive with a high RVP. They adjust the RVP of the final formulation to as high as 15.0 psi to help the gasoline ignite readily in the cold.
Step 6: Lubricate the drive and chassis.
Make sure all your parts are moving smoothly, also check the machine over for any missing or loose nuts and bolts that may have come loose. Start machine and run through all the gears and adjust cables if necessary.
Step 7: Adjust Scraper Bar and Skid shoes.
Check the scraper bar and skid shoes for wear, Adjust or replace for proper clearance.
After you've prepared your snow thrower for winter, start it up and let it run for a few minutes in a well-ventilated area just to be certain there are no surprises when it storms. Consider starting it every so often if it sits for an extended period.
Always use genuine OEM replacement parts when servicing your equipment. Use our parts finder to locate and order any replacement parts you may need for maintenance. Refer to your owner's manual for additional maintenance information.
Dropping temperatures and color-changing leaves usher in the colder months of the year. Taking some time now to do some basic maintenance can help save you time and frustration at the start of the next mowing season. This article will tell you how to prepare your Troy-Bilt riding lawn mower for off season storage. Depending on your model, the instructions listed below may vary slightly. Always be sure to check your Operator's Manual for detailed instructions.
Step 1 - Pre-Prep *Be sure the mower is on a flat, level surface. Turn the engine off and make sure it is cool. *Gather the necessary tools needed to complete the steps. Most Winterization procedures listed below can be completed with a basic mechanic’s tool kit.
Step 2 - Check and Replace Spark Plugs *Replace worn or damaged spark plugs. *Check your old spark plugs or your operator's manual for the correct part number.
Step3 - Change Oil *Change the oil and replace the filter. *Clean the oil fill and drain area of any debris. *Remove the dip stick from the oil fill tube. Remove the oil drain plug or use the oil drain valve and let the oil drain into the a oil pan. *Remove the oil filter. Using new oil, lubricate the gasket of the new filter, then install the filter. *Add new oil as instructed in your operator's manual. *Replace the dip stick. Start engine and let run for 30 sec then use the dip stick to check oil level.
Step 4 - Replace and Clean the Air Filter *Remove the air cleaner cover from the mower. Then, remove the paper and foam elements. *Wash the foam element in mild detergent and water and allow it to dry completely. *Apply a few drops of clean engine oil to the foam element and squeeze out all excess oil. *Replace the new paper element and the foam element into the air cleaner cover.
Step 5 - Replace the Blades and Clean the Mowing Deck *Clean and scrape the under side of the deck of dirt, grass clippings, and any other objects that may have become lodged there. *Wearing gloves for protection, inspect your blades for wear or damage. Use a Blade Removal Tool to hold the blades in place. *Then, using a socket, loosen the bolt securing the cutting blade to the spindle. Remove the blades. *Install new blades or sharpened blades and tighten the bolts to the proper torque as indicated in your operator's manual.
Step 6 - Check the Mower for Broken, Worn or Missing Parts Check the mower for any broken or worn parts including belt covers, belts, discharge chute, deck wheels and tires. Replace any of these worn or broken parts with the right OEM replacement parts as noted in your operator's manual.
Step 7 - Prepare the Fuel Tank for Storage Finally, add a fuel stabilizer to the fuel tank to prevent fuel from spoiling while the mower is not in use.
**If your fuel is more than 30 days old the fuel stabilizer may not work.
Step 8 - Disconnect and Remove Battery *Remove the black negative (-) cable and then the red positive (+) cable from the battery. Do not allow the wrench to come in contact with any metal. *Remove the battery from the lawn mower and store it in a warm, ventilated dry place.
As your one-stop-shop for all small engine service and repair needs, schedule your service appointment today with one of our trained, certified technicians.
