Exmark 116-0164 Hydro Filter | OEM Hydraulic Filter

Exmark 116-0164 Hydro Filter - OEM Hydraulic Filter Replacement

The Exmark 116-0164 Hydro Filter is a genuine OEM replacement hydraulic filter designed to help protect your mower’s hydro drive system from dirt, debris, metal particles, and fluid contamination. This filter helps remove contaminants from the hydraulic oil before they can damage hydro pumps, wheel motors, valves, and other expensive drive system components.

Using the correct OEM Exmark hydro filter helps support proper hydraulic flow, dependable drive performance, and long hydro system life. This filter is commonly used on select Exmark Lazer Z commercial zero-turn mowers, including E-Series, S-Series, X-Series, Z-Series, AS-Series, and related Lazer Z model families.

If your mower is due for hydro service, replacing the hydro filter with a genuine OEM Exmark filter is one of the best ways to help protect your commercial mowing equipment.

Product Details

Key Features

• Genuine OEM Exmark hydro filter
• Part number 116-0164
• Helps remove dirt, debris, and particles from hydraulic fluid
• Helps protect hydro pumps, wheel motors, and drive system components
• Supports proper hydraulic flow and hydro system performance
• Designed for compatible Exmark commercial mower hydro systems
• Recommended for routine hydro oil and filter maintenance
• Helps extend hydro system and equipment life when serviced properly

Check Common Model Fitment

Use the dropdown sections below to review common Exmark Lazer Z model families associated with Exmark 116-0164 Hydro Filter. This guide is simplified for easier shopping and is not a guarantee of fitment. Always verify with your full Exmark model number, serial number, original filter number, and parts diagram before ordering.

Important: The dropdown fitment guide is a simplified reference, not a guarantee of fitment. Exmark 116-0164 fits many Lazer Z models, but compatibility depends on your exact model, serial number, hydro system configuration, and parts diagram.

Maintenance Recommendation

For many Exmark hydro systems, it is recommended to change the hydro oil and hydro filters after the first 250 hours of operation, then every 500 hours after the first service interval. Service may be needed more often under severe mowing, high heat, dusty, wet, or heavy-use conditions.

Always follow the maintenance schedule listed in your Exmark operator’s manual for your exact mower model.

Why Replace Your Hydro Filter?

A clogged, restricted, or contaminated hydro filter can reduce hydraulic oil flow and increase stress on expensive drive system components. Replacing the hydro filter during routine service helps reduce the risk of pump damage, wheel motor wear, poor drive response, overheating, and premature hydro system failure.

Genuine OEM Exmark filters are designed to meet Exmark specifications for fit, filtration, sealing, and hydro system protection.

Important Fitment Note

Exmark 116-0164 fits select Exmark mower models only. Fitment can vary by model, serial number, hydro system setup, year, and parts diagram.

Before ordering, confirm:

• Your full Exmark model number
• Your Exmark serial number
• Your original hydro filter part number
• Your hydro oil service requirements
• Your Exmark parts diagram
• Whether your mower uses Exmark 116-0164

If you are unsure, contact P&P Small Engines with your full model and serial number before ordering.

Part Number / Search Terms

Exmark 116-0164 may also be searched as:

• 116-0164
• 1160164
• Exmark 116-0164
• Exmark 1160164
• Exmark hydro filter
• Exmark hydraulic filter
• Exmark hydraulic oil filter
• Exmark Lazer Z hydro filter
• Exmark Lazer Z hydraulic filter
• Lazer Z hydro filter
• E-Series Lazer Z hydro filter
• S-Series Lazer Z hydro filter
• X-Series Lazer Z hydro filter
• Z-Series Lazer Z hydro filter
• Lazer Z AS hydro filter
• LRS hydro filter
• LRX hydro filter
• LZA hydro filter
• LZAS hydro filter
• LZE hydro filter
• LZS hydro filter
• LZX hydro filter
• LZZ hydro filter

Frequently Asked Questions

Is Exmark 116-0164 an OEM hydro filter?

Yes. Exmark 116-0164 is a genuine OEM Exmark hydro filter.

What does the Exmark hydro filter do?

The hydro filter removes dirt, debris, and particles from hydraulic fluid to help protect hydro pumps, wheel motors, valves, and other hydraulic system components.

What models does Exmark 116-0164 fit?

It is commonly used on select Exmark Lazer Z mowers, including E-Series, S-Series, X-Series, Z-Series, AS-Series, LRS, LRX, LZA, LZAS, LZE, LZS, LZX, and LZZ model families. Always verify fitment by full model and serial number.

When should I replace my Exmark hydro filter?

Many Exmark hydro systems recommend changing hydro oil and filters after the first 250 hours, then every 500 hours after that. Severe operating conditions may require more frequent service.

Can I use this filter without checking my model?

No. Always verify your full Exmark model number, serial number, original hydro filter part number, and parts diagram before ordering.

Why use an OEM Exmark hydro filter?

OEM Exmark filters are built for proper fit, sealing, filtration performance, and compatibility with supported Exmark hydro systems.

P&P Small Engines stocks genuine Exmark hydro filters, belts, blades, pulleys, idlers, maintenance parts, and commercial mower replacement parts to help keep your equipment ready to work.